320040 - How to: Use Ntdetect.chk to Identify Hardware Problems in Windows 2000

This step-by-step article describes how to use the debug version of Ntdetect.com (Ntdetect.chk) to help you to identify hardware problems that may prevent your computer from starting. 

If you are experiencing problems starting your computer because of a hardware problem, you can use Ntdetect.chk to determine the hardware component that may be causing the problem. Ntdetect.chk is located in the Debug.cab file from the Windows 2000 Resource Kit companion compact disc (CD). Open the Debug.cab file, and then extract the Ntdetect.chk file.

Back to the top

How to Use Ntdetect.chk to Identify Hardware Problems

This section describes two methods that you can use to identify hardware problems.

Method 1: Use Ntdetect.chk to Start the Computer from the Windows 2000 Setup Boot Disks

1. Create a duplicate copy of Setup disk 1 from the Windows 2000 Setup boot disks.For additional information about how to create startup disks for Windows 2000, click the article number below to view the article in the Microsoft Knowledge Base:
   197063  How to Create Setup Boot Disks for Windows 2000
2. Rename the Ntdetect.com file on the copy of the Windows 2000 Setup boot disk that you created in step 1 to "Ntdetect.bak."
3. Extract the Ntdetect.chk file from the Debug.cab file on the Windows 2000 Resource Kit CD to the Windows 2000 Setup boot disk.
4. Rename the Ntdetect.chk file on the copy of the Windows 2000 Setup boot disk to "Ntdetect.com."
5. Insert the copy of the Windows 2000 Setup disk that you created in step 1 in drive A, and then restart the computer.

Method 2: Use Ntdetect.chk to Start the Computer from the Hard Disk

If you do not want to use the Windows 2000 Setup boot disk, use the following procedure to replace the Ntdetect.com in the root folder of your system partition. 

NOTE: Depending on the current state of your computer, you may have to start the computer in safe mode or use the Windows Recovery Console to perform the procedure that is described in this section. 

You can use the Recovery Console to help recover a Windows-based computer that either does not start properly or does not start at all. If safe mode and other startup procedures do not work, you may want to use the Recovery Console. Microsoft recommends this method only if you are an advanced user who can use basic commands to identify and locate problem drivers and files. Additionally, you must be an administrator to use the Recovery Console. For additional information about how to start Windows in safe mode, click the article number below to view the article in the Microsoft Knowledge Base:

281770  How to Perform Clean-Boot Troubleshooting for Windows 2000

To use Ntdetect.chk to start the computer from the hard disk:

1. Rename Ntdetect.com to "Ntdetect.bak" in the root folder of your system partition.
2. Extract the Ntdetect.chk file from Debug.cab file in the Windows 2000 Resource Kit CD-ROM to the root of your system partition.
3. Rename Ntdetect.chk to "Ntdetect.com" in the root folder of your system partition, and then restart the computer.

Back to the top

How to View the Results

If you run the debug version of Ntdetect.com, hardware information is displayed when it is detected. To move to the next window, press any key. Continue until Setup stops responding (hangs). Review the contents of the window that is displayed when Setup stops responding to determine the hardware component that may be causing the problem.

The following is text is an example of the contents that may be displayed:

Detecting System Component . . .
Reading BIOS date . . .
Done reading BIOS date (1/20/2002)
Detecting Bus/Adapter Component . . .
Collecting Disk Geometry . . .
Detecting Keyboard Component . . .

After Ntdetect.com displays information about the components, press ENTER for Ntdetect.chk to continue. Ntdetect.chk displays information about the current nodes for the controllers and peripherals. You must press ENTER after you view each window.

NOTE: After you finish using Ntdetect.chk, Microsoft recommends that you rename Ntdetect.com to "Ntdetect.chk," and then rename Ntdetect.bak to "Ntdetect.com."

Back to the top

Troubleshooting

The Hidden, System, and Read Only attributes are configured on Ntdetect.com when you install Windows 2000. You must clear these attributes to make the file visible. Use either My Computer, Microsoft Windows Explorer, or the command prompt to change these attributes.

How to Use Either My Computer or Windows Explorer to Change File Attributes

1. Open My Computer or start Windows Explorer.
2. Click Folder Options on the Tools menu.
3. Click the View tab, click Show hidden files and folders in the Hidden files and folders section.
4. Click to clear the Hide protected operating system files (Recommended) check box, click Yes, and then click OK.
5. Click the Ntdetect.com file that is located in the root of the C drive.
6. Click Properties on the File menu.
7. Click to clear the Read Only check box and the Hidden check box in the Attributes box of theGeneral tab, and then click OK.

How to Use Either the Command Prompt or the Recovery Console to Change File Attributes

To use either the command prompt or the Recovery Console to change the file attributes, type attrib -s -h -r ntdetect.com, and then press ENTER. 

DELL OPTIPLEX 380 driver & other utilities download

                                                           

System Utilities > Dell System Software

http://www.dell.com/support/drivers/us/en/04/DriverDetails?DriverId=NJ7GT&FileId=2731099470&DriverName=Dell%20System%20Software%2C%20v.6.3.4%2C%20A06&productCode=optiplex-380&urlProductCode=False

Chipset > Intel Chipset Software

http://www.dell.com/support/drivers/us/en/04/DriverDetails?DriverId=R0JHR&FileId=2939911475&DriverName=Intel%20Chipset%20Software%20Installation%20Utility%2C%20v.9.1.1.1025%2C%20A02&productCode=optiplex-380&urlProductCode=False

Video Driver > Intel G41 (intel) Graphics Controller

http://www.dell.com/support/drivers/us/en/04/DriverDetails?DriverId=R296582&FileId=2731117566&DriverName=Intel%20Q43%2FQ45%2FG43%2FG45%20(Eaglelake)%20Graphics%20Controller%2C%20G41%20(intel)%20Graphics%20Controller%2C%20v.6.14.10.5322%2C%20A06&productCode=optiplex-380&urlProductCode=False

Audio > Realtek ALC269 HD Audio

http://www.dell.com/support/drivers/us/en/04/DriverDetails?DriverId=XF89F&FileId=2731093227&DriverName=Realtek%20ALC269%20HD%20Audio%2C%20v.5876%2C%20A03&productCode=optiplex-380&urlProductCode=False

Network > Broadcom 57XX Gigabit Integrated

http://www.dell.com/support/drivers/us/en/04/DriverDetails?DriverId=YMHGV&FileId=2731101343&DriverName=Broadcom%2057XX%20Gigabit%20Controller%2C%20v.16.4.0%2C%20A07&productCode=optiplex-380&urlProductCode=False

Hope that everything is satisfactory. If there are further enquiries or concerns, please feel free to contact us or drop me an email. We will be most glad to assist.

For any further technical information, products related support, latest news and  highlights, kindly click on the link to access our Dell Customer Support Site: http://support.ap.dell.com

Thank you.


Note: for esa users, please find the downloaded files from S:\Drivers\Desktop\Optiplex 380 - Windows XP 32 bit. TQ

How to synchronize the time with the windows time service in windows XP

W32tm /config /[/computer:<target>] [/update]

W32tm /resync

Due to server time was not updated. I manually change the server time & resync one by one to be available on the network by using command:-

Open CMD
Type: w32tm /resync /computer:computername <enter>
example:
w32tm /resync /computer:esapc00

The following error occurred: Access is denied. <0x0070005>

The following error occurred. The RPC Server is unavailable. <0x800706>

How to make sure the time at server is up to date?

Apply the following settings:

Open CMD
Type: w32tm /config /computer:esaserver /update /manualpeerlist:time.windows.com /syncfromflags:manual /reliable:yes <enter>

The command should completed successfully.

Could not copy & paste file to kingston controller 8GB or format it.

Error message: Write protected
Shared-Nothing happened.

Solution:

To change at Register Editor:

The registry file is downloadable at:

http://www.keepandshare.com/doc/4170618/disableusbwrite-zip-june-20-2012-11-58-am-1k?da=y

Unzipped the folder. Then run the file.
Filename: DisableUSBWrite.

Windows Registry Editor 5.00

HKEY_Local_Machine\system\currentcontrolset\control\storagedevicepolicies]
"Writeprotect"=dword:00000001

Could not open Microsoft Office Starter 2010

Could not open Microsoft Office Starter 2010

Error message: Repair Microsoft Office Click-to-Run.

Repairing Microsoft Office Starter 2010 - English was unsuccessful because an internet connection is required.

Solution 1:

1. Close all programs.
2. Restart PC 
3. Re-login to your PC
4. Open Microsoft Office program.
5. The Microsoft should working fine now.